Thanks. not only is a conneciton not accepted on that port, there's no sign that a device exists on that port at all. If the router is still under warranty, call Cisco for support. I told you not to run any of that or use the CD...This is all you do.. http://cygnussoft.com/linksys-router/linksys-router-internal-error-302.html
By default this is set to Linksys (or some variation thereof). Then go to www.grc.com and run Shields-Up to confirm the ports are actually open.Phil P.S. Pull the power cord from the cable modem, make sure the lights go off and leave it off.2. You can set up your router manually, without the CD.
Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual PCA-6186 REV A1 User manual.pdf.... I am now using an ASUS P5K-E, where I had been using a ASUS P5AD-2 Deluxe. Or just drag it here! Expert: Network Bill replied6 years ago.
and 4 other Networking Specialists are ready to help you Ask your own question now Customer: replied7 years ago. Try switching cables (if possible) to make sure it is not a cable issue. Tuesday, August 30, 2011 5:29 AM Reply | Quote 0 Sign in to vote If ShieldsUp is not showing the Port as being open (red square) then it's almost certainly not Ask Your Own Networking Question Customer: replied6 years ago.
or it's affiliates. Getting 10/16/2016 10/16/2016 Byron I'm trying to log in to the computer that acts as our server 10/16/2016 10/16/2016 WesPCDr X Ask a Network Technician Get a Professional Answer. 100% Satisfaction The username is XXXXX XXXXX but the password XXXXX XXXXX whatever you just created. https://community.linksys.com/t5/Wireless-Routers/Error-Message-302-on-Model-WRT54G2/td-p/319219 Credentials confirmed by a Fortune 500 verification firm.
Question about WRT160N Wireless Router 1 Answer When I tried to install ...Internal Error. On Sun, 11 Sep 2011 23:09:49 +0000, Bill - whgj wrote: > So I have manualy configured, finally got Shields-Up to give me a red light on port 443 but WRT160N Wireless Router Manual WRT160N Wireless... What does this message mean?
from above...Ok let's not use the CD, let's just install it manually.Before following these directions, please make sure everything is wired correctly. I close the installguide, remove CD, start PC again, insert CD, start installing, get error 302 agin etc.How do I solve this problem.TX, Wim Rijff Share this conversation Expert: Viet Check with your service operator for a fresh config details to enable the router in gateway Question about Xtreme N DIR-655 Wireless Router 1 Answer When setting up my new D=Link Thanks for the help.
Filter By: dir connect 655 xtreme internal message d setup zohne trendnet 1,043 questions posted Ask a Question Usually answered in minutes! have a peek at these guys Login|Contact Us Networking Ask Computer Networking Questions and Get Answers ASAP Not a Networking Question? a password?Viet - Network Tech : yes, it's a passwordCustomer: settings saved!Viet - Network Tech : great.Viet - Network Tech : now from your laptopViet - Network Tech : connect to I've done all that but the router doesn't even recognized my internet or port 1, 2, 3, or 4.
You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Share this conversation Related Networking Questions Question Date Submitted Am unable to pick up any signal on 3G or WI-FI, phone and 10/18/2016 10/18/2016 Dan I recently had ATT Uverse wifi I am supposing it was testing access to imaginary port usage including cameras and such (judging by the labels, there were a bunch of them as the list was full). check over here only your cable provider can update DOCSIS devices like this even if you own it yourself.
Port 4125 was required for RDP with WHS1, but you can do RDP with WHS 2011 with only 443 - that's the standard configuration with no special setup required. PDF Manual Icflogin.pdf. Close Internet Explorer.That's it!
How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Now unplug the power cord from the Linksys, make sure the lights go off.3. you can ... don't...
Question about Routers 1 Answer Router setup gets Error 302 message ...Error 302 message Reset router and used Quick Router Setup disk. Ask Network Bill Your Own Question Network Bill, Certified Networking Engineer Category: Networking Satisfied Customers: 1070 Experience: BSIT, Cisco Certified Network Associate, A+ Hardware, Sun Solaris I, Microsoft Certified System Eng. Actually, I had to download the setup wizard from the Linksys website because I could not find the CD. this content I have not had an occasion to confirm.
Yikes! DSL? You don't have a strange network configuration do you with more than one router?Phil P.S. I've also tried disabling my firewall and it still doesn't work.
Tuesday, August 30, 2011 10:19 AM Reply | Quote 0 Sign in to vote Are ISPs likely to open a port for an individual home user in your experience? Even if you are not using wireless computers you should still do this step because it prevents others from stealing your Internet service. I assume that indicates either my ISP (cox.net) is locking me down or my router is not really following instructions when I tell it to forward Port 443 to my WHS, Ask Viet - Network Tech Your Own Question Viet - Network Tech, Computer Support Specialist Category: Networking Satisfied Customers: 34652 Experience: Great troubleshooting skills with computer and network. 30037186 Type Your
Reset again but now get Error 302: Internal Error. If you find my comment helpful or if it answers your question, please mark it as such. Okay. How can I re-setup my router?
Dante Level 3 Expert 623 Answers Mike Level 3 Expert 4326 Answers Are you a Linksys Router Expert? On four separate occasions the difficult to understand Linksys tech (?) ultimately determined that ...