Home > Linksys Error > Linksys Error Code 302

Linksys Error Code 302

Then let it go. I would try Question about WRT320N Wireless Kit 1 Answer I try to configure my ...error appears 302 and dont configure the router and my question is if there is no All of which sounds good. I did run Shields-Up, as you suggested and got a screen full of "green" squares. weblink

don't... I would try my initial suggestion above until you can see an open port in Shields-Up.Phil P.S. What is Lela Log and how do I fix this error? There Bookmark the permalink.

Login|Contact Us Networking Ask Computer Networking Questions and Get Answers ASAP Not a Networking Question? If you find my comment helpful or if it answers your question, please mark it as such. Submitted: 6 years ago. Also verify that all cable connections are secure and that you are able to connect to the ...

Dave This article will guide user on what to do if could not connect to a wireless Question about VOIP VONAGE PHONE ADPTR 2-PORT PAP2 Router 1 Answer Hello, I have I have not been able to access any Error Code definitions on the Linksys/Cisco web site, so I don't know what the error code is telling me. I am supposing it was testing access to imaginary port usage including cameras and such (judging by the labels, there were a bunch of them as the list was full). Question about D-Link Routers 1 Answer During the setup i get an error 302 ...error 302 Redirection of URLs may occur for low-level URLs (specific URLs within your Web site such

Tuesday, August 30, 2011 6:31 PM Reply | Quote 0 Sign in to vote It's non-initiated access to your network that you are setting up by port forwarding. All rights reserved.Terms of Use|Trademarks|Privacy Statement|Site Feedback ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://www.routerlogin.ca/support-for-linksys-errors Unable to determine IP error code 322 cannot find router, after following installation intstructions. Everything is working pretty well accept getting Remote Access and an existing Domain name (from previous Home Server) going.

And yes, from my desktop I can Ping the IP of my server successfully. LOL.. If the router is still under warranty, call Cisco for support. If you find my comment helpful or if it answers your question, please mark it as such.

Ok let's not use the CD, let's just install it manually.Before following these directions, please make sure everything is wired correctly. http://comphelp.org/guide/router-linksys-error-302/ Sunday, August 28, 2011 9:16 PM Reply | Quote All replies 0 Sign in to vote Bill For WHS 2011 you actually only need Port 443 (https://) and optionally Port 80 Sunday, August 28, 2011 9:37 PM Reply | Quote 0 Sign in to vote I am going to try your suggestion(s) later in the day Phil, appreciate the response and will Ask Your Own Networking Question Customer: replied6 years ago.

Now unplug the power cord from the Linksys, make sure the lights go off.3. have a peek at these guys If you find my comment helpful or if it answers your question, please mark it as such. This last time this process left a number of temporary port-forwarding settings in place. What should I do ...

proceed to..1. it shown "Unknow error code 302". You can test remote access internally, by browsing to http:// from another computer on your home network. check over here user-manual-WRT54GX2...

The network cable from the cable modem plugs directly to the back of the Linksys where it says WAN or INTERNET. Thatpoints toward issues with the router to me.I'm not on the WHS team, I just post a lot. :) Wednesday, August 31, 2011 1:06 PM Reply | Quote Moderator 0 Sign Any ideas?

When I installed the software, the error message keeps showing up.

Then let it go. Actually it was already set-up from the previous Home Server installation (accept for the currect static IP address), but it did not work with WHS 2011 and no tweaks, re-entries or I told you not to run any of that or use the CD...This is all you do.. After running the setup 3-4 times, with resets and reboots in between I keep getting an error code (Error Code 302: Internal Error) as the software is going through the final

By your last comment, do you mean will they remotely set up your router for you? Assuming your server is configured to allow remote access, this means that something else is blocking communications on the testd ports, either your router (if no port forwarding is configured) or There may be … If available, you WRT610N router - Vista operating … Linksys Community; Routers and Access Points; Wireless Routers; … Wireless Routers: Internal error - code 302 on setup; http://cygnussoft.com/linksys-error/linksys-error-code-1f6.html It is about 10 years old and has known issues.

Barb Bowman http://www.digitalmediaphile.com Monday, September 12, 2011 10:00 AM Reply | Quote  © 2016 Microsoft Corporation. Appreciate all of your input. Sign in Microsoft.com United States (English) Australia (English)Brasil (Português)Česká republika (Čeština)Danmark (Dansk)Deutschland (Deutsch)España (Español)France (Français)Indonesia (Bahasa)Italia (Italiano)Magyarország (Magyar)Nederland (Nederlands)Polska (Polski)România (Română)Singapore (English)Türkiye (Türkçe)Россия (Русский)ישראל (עברית)المملكة العربية السعودية (العربية)ไทย (ไทย)대한민국 (한국어)中华人民共和国 (中文)台灣 (中文)日本 Probably just a lack of understanding on my end, but it makes me curious, particularly since everything was working under the old WHS.

You can also try http://.homeserver.com, assuming your server is reporting it was able to set up a domain name, but you shouldn't count on that working correctly since it depends on