Then go to www.grc.com and run Shields-Up to confirm the ports are actually open.Phil P.S. As a matter of fact I would suggest replacing it on general principles once other issues are as sorted (as they can be). Everything else you would expect from your server is working? Then let it go. http://cygnussoft.com/linksys-error/linksys-error-211.html
If it were me I would actually stop trying to use the setup CD and just configure the router manually. HiCustomerand thanks for choosing Just Answer. Wait about a minute.4. When you are sure that is correct.. https://community.linksys.com/t5/Wireless-Routers/Error-Message-302-Internal-Error/td-p/393225
On Tue, 30 Aug 2011 20:08:47 +0000, Bill - whgj wrote: >After running the setup 3-4 times, with resets and reboots in between I keep getting an error code (Error You should not need to adjust the firewall. did you follow my instructions? I have rebooted the modem and computer several times and that didn?t help.
Switch just hosts a couple of printers that are remote to my router. Are ISPs likely to open a port for an individual home user in your experience? Afterwards unable to connect to Internet. characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 54 4920595 Login|Contact Us Networking Ask Computer Networking Questions and Get Answers ASAP Not a Networking
You can set up your router manually, without the CD. As well, backup, folders, dashboard and RDP access from my desktop to my server all works fine. Getting 10/16/2016 10/16/2016 Byron I'm trying to log in to the computer that acts as our server 10/16/2016 10/16/2016 WesPCDr X Ask a Network Technician Get a Professional Answer. 100% Satisfaction visit So far I have not been successful.
This one must match your ISP. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Are your computer monitor colors considerably off? Please click on Accept if my answer has been helpful.
Ask Your Own Networking Question Customer: replied6 years ago. http://www.justanswer.com/computer-networking/2xgr7-does-linksys-router-meant-error-302-internal.html My name is XXXXX XXXXX I will be happy to assist you with this problem.I understand you are getting error 302 when running the setup of your new Linksys router correct? Actually it was already set-up from the previous Home Server installation (accept for the currect static IP address), but it did not work with WHS 2011 and no tweaks, re-entries or Credentials confirmed by a Fortune 500 verification firm.
I've also tried disabling my firewall and it still doesn't work. http://cygnussoft.com/linksys-error/linksys-error-321.html Everything is working pretty well accept getting Remote Access and an existing Domain name (from previous Home Server) going. Bill Monday, August 29, 2011 9:31 PM Reply | Quote 0 Sign in to vote Yes. Tuesday, August 30, 2011 6:31 PM Reply | Quote 0 Sign in to vote It's non-initiated access to your network that you are setting up by port forwarding.
Thatpoints toward issues with the router to me.I'm not on the WHS team, I just post a lot. :) Wednesday, August 31, 2011 1:06 PM Reply | Quote Moderator 0 Sign Tuesday, August 30, 2011 8:08 PM Reply | Quote 0 Sign in to vote ...After running the setup 3-4 times, with resets and reboots in between I keep getting an error Assuming your server is configured to allow remote access, this means that something else is blocking communications on the testd ports, either your router (if no port forwarding is configured) or check over here Whileit's possible that your ISP will open some ports for you, it's also unlikely.
You can test remote access internally, by browsing to http://
Question about Routers 1 Answer Wireless connection DLink Dir-825 to printer lost. ...reset router, now can't connect to Internet. On a new WRT160N these are both admin - click OK after entering and you should be allowed into the router.You will be presented with the Basic Setup page. from above...Ok let's not use the CD, let's just install it manually.Before following these directions, please make sure everything is wired correctly. Sign in Microsoft.com United States (English) Australia (English)Brasil (Português)Česká republika (Čeština)Danmark (Dansk)Deutschland (Deutsch)España (Español)France (Français)Indonesia (Bahasa)Italia (Italiano)Magyarország (Magyar)Nederland (Nederlands)Polska (Polski)România (Română)Singapore (English)Türkiye (Türkçe)Россия (Русский)ישראל (עברית)المملكة العربية السعودية (العربية)ไทย (ไทย)대한민국 (한국어)中华人民共和国 (中文)台灣 (中文)日本
Sunday, August 28, 2011 9:16 PM Reply | Quote All replies 0 Sign in to vote Bill For WHS 2011 you actually only need Port 443 (https://) and optionally Port 80 How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. All of which sounds good. this content Ask Your Own Networking Question Customer: replied6 years ago.
Expert: Network Bill replied6 years ago. Tuesday, August 30, 2011 5:29 AM Reply | Quote 0 Sign in to vote If ShieldsUp is not showing the Port as being open (red square) then it's almost certainly not Filter By: dir connect 655 xtreme internal message d setup zohne trendnet 1,043 questions posted Ask a Question Usually answered in minutes! However, I should let you know I had no problems under the old WHS installation, only since installing WHS 2011.
That the Green squares are showing means people can't probe inside your network. I am supposing it was testing access to imaginary port usage including cameras and such (judging by the labels, there were a bunch of them as the list was full). This is a new/different motherboard and processor for my new WHS 2011 install.