Home > Lexmark Printer > Lexmark Printer X5150 Hardware Error 0502

Lexmark Printer X5150 Hardware Error 0502

Reply Auto says: 2008-12-13 at 2:37 am Thanks for the tip Had the 0502 error on a Lexmark all in one at the office that we use mainly for scanning I After this triumph, I attempted to attach the encoder strip to the back of the cartridge carrier as they advise on the Dell website. Reply Susan says: 2010-01-08 at 2:07 pm thanks - very helpful tip and you've saved me a lot of time stuffing around with my printer!!! Reply John says: 2007-09-26 at 2:52 am I tried cleaning both the rail and the encoder strip and still have the 0502 error. http://cygnussoft.com/lexmark-printer/lexmark-printer-hardware-error-0502.html

I need photos. ok sir pls see the link this is the helpfull for the error 0502 in lexmark x160 all in one inkjet printer...ok ... I love this old dog printer-had it over 5 years now and just wanted to keep it going, as money is tight. Please help. http://support.lexmark.com/index?productCode=LEXMARK_X5150&segment=SUPPORT&page=content&id=HO2707

Inloggen 1 10 Vind je dit geen leuke video? Saved me getting the technicians in at work (made me look good in front of the boss too!). As WSnipes advised I placed the side with the F and the down arrow on the left side. Thank you!

Now, does anyone have a fix for the paper feed problem where the paper grabs from one side about 70% of the time? They operate in unison with the paper rollers that position the paper line by line as needed for the print job..if they get out of alignment, the printer cannot function. Disconnect the power cable from the back of the Lexmark X5100 / X6100 Series. 3. Perform the hardware test without cartridges first and then with both cartridges.* 12.

MSnipes said that the left side contains the F and the Right side is the one marked D. Any ideas.???? Reply thet Later herinneren Nu bekijken Conform de wetgeving ten aanzien van de bescherming van gegevens verzoeken we je even de tijd te nemen om de belangrijkste punten van ons Privacybeleid Reply Bob says: 2009-12-12 at 7:32 pm Thanks for the wonderful tip - I was sure I would have to purchase a new printer and did not want to.

I almost threw it in the trash yesterday. I have taken out, cleaned, shaked to get rid of any possible airbubbles, wiped inside, all a few times and still nothing! I figured that I'd share my experience in the event anybody else runs across this issue, which was amusing enough to make me chuckle. 😉 Reply denise says: 2007-05-02 at 12:04 Hope this helps someone out there.

For folks still stymied, try powering up without the cartridges. http://fixyourownprinter.com/forums/printer/34491 Excellent document on how to fix this error here: http://blog.forret.com/2006/02/lexmark-printers-with-hardware-error-0502/ Please rate this solution, thanks! lexmarx x5150 - cleaning metal rod A++++ Reply Alan says: 2008-11-17 at 3:48 pm It worked! Refer to this article in the Lexmark website on Error 0502 on the ...

But I persisted. check over here MR Reply Grandma says: 2009-12-12 at 4:35 am Thank you! The magenta ( red ) did not work as well. Help, Thanks Reply Cindy D says: 2008-12-05 at 9:50 pm I have a Lexmark P4350.

Over Pers Auteursrecht Videomakers Adverteren Ontwikkelaars +YouTube Voorwaarden Privacy Beleid & veiligheid Feedback verzenden Probeer iets nieuws! I had been getting the “0502″ error on my Lexmark 5150. The 0502 error can be caused by four different issues: A contaminated encoder strip ... http://cygnussoft.com/lexmark-printer/lexmark-printer-x6170-hardware-error-0502.html ps alcohol works best Reply Dave says: 2010-01-04 at 1:57 pm Worked ok,many thanks Reply gadgetgirly says: 2010-01-05 at 7:05 pm THANK YOU THANK YOU THANK YOU…your a lifesaver. (and the

Wrote about the encoder strip popped out of its slot on the cartridge carrier. Now the silly thing decides to quite printing all together. wish i saw this site first!

says: 2007-12-16 at 10:35 pm you have just saved my printer life 😀 I was about to throw it of the window ….

Reply Joanna says: 2006-11-26 at 7:49 pm Thanks for the awesome tip! Becky Reply morandi says: 2008-09-27 at 7:33 pm TENGO EL ERROR 0502 EN MI IMPRESORA LEXMARK X5150 ,POR FAVOR QUISIERA ME ENVIARAN INSTRUCCIONES PARA SOLUCIONARLO, YA LIMPIE BARRA DE METAL, PERO Thank you! You can see exactly how it's supposed to seat from the left side of the printer through a cutout in the metal with a flashlight (your right).I put this all back

I Googled this and found your site first. IT ALWAYS SOMETHING GOING WRONG WITH THEM.I HAVE KNOICA MINOLTA 2400 MAGIC PRO. Thanks again Reply ROI says: 2008-05-02 at 7:20 am Printer blows….cartridges are like $60 for both…take your money and get a new one - HP anything. weblink Clean the encoder strip with an alcohol swab GENTLY…the encoder strip is attached on a spring system on one end and to a metal tab on the other.

One end has the letter ‘F' the other ‘D'. Could not find any help until I decide to google my problem. You saved me lots of money and saved the printer unnecessary disposal! I think I need to remove the top part of the printer but How do I do that?

I ended up ripping the square hole on the end-open. Reply Adam says: 2008-01-22 at 3:24 am Used a napkin & hardley got off any grease but that fixed it. I am not sure if it makes any difference at all which way it goes in.