Home > Lexmark Printer > Lexmark Printer Error Code Ec5

Lexmark Printer Error Code Ec5

Contents

Replace low voltage power supply assembly. I will have purchasing call in an order. Newer machines display a sub code to indicate which condition applies. For more information, see Jams and misfeeds. Paper out The All-In-One is out of paper. this contact form

Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. Make sure top access door is closed securely 2. Press Select.

Lexmark Printer Error Code Ec5

Insert a memory card with a correct or supported format. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Make sure the memory shown on the printout matches the installed memory.

Observe the lamp through the left near side of the printer. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Press Select to select a new blank paper size, or press Stop/Clear to cancel the current DPOF print job. Lexmark Printer Error Lights Press Select.

Replace the transfer roller as necessary. Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write. Delete old scans or files that you no longer need to free up disk space. Try opening Tray X.

Press "GO" to clear message and temporarily continue Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of it's life and must be 938.06 Service System Electronics A second memory card is inserted. Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.

Lexmark Printer Error Messages

Error 47 47 Font Card Removed While Printing Printer needs data on removed card. Check AC power source for noise. Lexmark Printer Error Code Ec5 Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Lexmark Engine Error Press Stop/Clear on the control panel to cancel printing.

Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. weblink Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Load plain paper. Perform fuser service check. Lexmark Error Codes Problem

Thank you and your firm again, you were terrific. POR several times Check each board for secure ground. Install a print cartridge. navigate here Load paper, and then resume the print job. No computer The All-In-One is not connected to a computer, or the computer is off when one of the start buttons (Color and

If you are installing a black or photo cartridge, insert it in the left carrier. Lexmark Ms310dn Error Codes Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset. Verify correct cable connections from the Engine board to the HVPS.

Can be system board or printhead.

Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Open doors and covers and remove the toner cartridge. Ensure the transparent tape is removed from both cartridges. Lexmark Crc Failed Do Not Power Off We got it this morning and I have it installed.

Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. For more information, see Removing a used cartridge and Installing the print cartridges. Paper jam There is a paper jam. While in Photo mode, a memory card with no images is inserted. his comment is here Consider purchasing more memory for the computer.

System Board Pricing Request Quote 975-979 Network Card X Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 975- Unrecognizable Network Card 976- Unrecoverable Ensure your computer is connected and turned on. Carrier Jam There is a cartridge carrier jam. Scroll Down to your error code.... Press Select to retry alignment. Photo mode A memory card is not inserted correctly or is damaged.

Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. A secondary error indication can be obtained by pressing an releasing a button.

Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers Error message or title What it indicates Solution Ink low The print cartridge is running out of ink. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Reconnect.

Replace the assys in the following order 1. John D. Open the printer rear door to access the jam.