Home > Lexmark Printer > Lexmark Printer Error 0502

Lexmark Printer Error 0502

Ask RPI Solutions Your Own Question RPI Solutions, Support Specialist Category: Computer Satisfied Customers: 9561 Experience: 5+ Years in IT, BS in Computer Science 14124282 Type Your Computer Question Here... Slightly push the encoder strip down and then back up to get it into the slot. 8. Gently slide the ink cartridge carrier to the middle of the printer. 4. Sign Up Login Add Question dlajsr asked Dec 17, 2005 at 6:10pm 0 Unknown Printer Lexmark X6150 Hardware Error Code 0502 After starting any operation it displays "Hardward error 0502".Will usually navigate here

Clean the encoder strip with a dry tissue. I figured the red (magenta) might not work because something was unplugged. MANUALLY move cartridge carriers towards the center.4. Reconnect the power cable and switch the printer on again. 11.

Expert: RPI Solutions replied7 years ago. Place an index finger on the encoder strip on either side of the cartridge carrier. 7. Submitted: 6 years ago. If the printer fails to print, remove both cartridges and try the test again. (It will feed the paper through and print a blank page.) 5.

with picture included: Re-position the Encoder Strip on your Printer To re-position the encoder strip, perform the following steps: 1. I found out through Lexmark tech support how to do this. I had to persuade them to tell me. Roberts is online now Lexmark printer x6100 says hardware error 0502 what does that Customer Question Lexmark printer x6100 says hardware error 0502 what does that mean Submitted: 5 years ago.

Sangram Rath 13.223 προβολές 2:00 Lexmark X6170 Printer Review - Διάρκεια: 2:38. by unknown on Feb 1, 2007 at 12:11pm Add comment Please sign in to comment I have the very same problem. fastprintersdotcom 107.613 προβολές 6:43 COMO INSTALAR UN SISTEMA DE TINTA CONTINUA EN HP 4500 - Διάρκεια: 6:47. http://support.lexmark.com/index?productCode=LEXMARK_X5150&segment=SUPPORT&page=content&id=HO2707 How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question.

The front top casing and the bottom casing SEEM fused together, but they come apart and snap back together. Your Own Question Freddy M., Technician Category: Printers Satisfied Customers: 18398 Experience: Years of IT and customer support experience 15852642 Type Your Printers Question Here... Also clean the contacts of the printer. 10. These are to your left when facing the printer.

Press the Option button 10 times until Cartridges appears on the LED display. 2. http://support.lexmark.com/index?page=content&id=SO1516&actp=LIST_RECENT When I try to test print a page a message says there is a print job in progress but when I open the printing queue there are no jobs pending. The magenta ( red ) does not work. If the encoder strip was re-seated correctly, the Hardware Error: 502 code will not appear.

Submitted: 7 years ago. check over here These are typically in warenty from lexmark. Ask Freddy M. The cartridge holder is still frozen and will not move.

There are two rubber seats and an electronics card full of ink over there. by unknown on Mar 29, 2011 at 3:36pm Add comment Please sign in to comment 0 I'm glad I spent the 4 hours fixing and logging how to fix your printer Es gab einen Fehler bei der Anwendung. http://cygnussoft.com/lexmark-printer/lexmark-printer-hardware-error-0502.html Look around with a flashlight to see how back cover of printer and forward top cover of printer fit in to get an idea of how the back casing and front

Credentials confirmed by a Fortune 500 verification firm. Each wire strip can get unplugged from its bay in the main part of the printer which allows the scanner top to be fully removed from the printer. Hello, Have you tried this?

Roberts replied5 years ago.

If the copy is satisfactory, repeat the test once to confirm that the error is gone.How to Perform the Hardware Test on the Lexmark X5150 ID:ENUS3744Using the operator panel on the Why does this printer hate me? I even saw a pic of how to do it. Perform the hardware test without cartridges first and then with both cartridges.* 12.

These printers were not that expensive, so may it is time.....I have cleaned the strip & metal bar in the past and I have been OK....then the issue began again.......so will Make a standalone copy. 13. I will try and play with plastic strip Expert: Charles A. weblink Lightly press the strip first to the rear and then forward, if necessary. 9.

I bought a new X5150 off Ebay. Using an index finger, gently push encoder strip down and then back up to get it back into the slot located on the back of the ink cartridge carrier. This occurs when attempting all operations, Maintenance, cleansing, copying etc... Place an index finger on the encoder strip on either side of the cartridge carrier. 7.

Lexmark states that they dont carry these parts and preety my advised me to buy a new multi-function device. The printer should print a sheet of paper with one black bar and one grey bar. 4. Once the encoder strip has been re-seated, close the lid to the unit. 9. move carriers to the RIGHT.6.

Press Select. The WI-FI connection is no longer working. Used alcohol.I unplugged all wires where I could see that they unplug and plugged them back in. and other Printers Specialists are ready to help you Ask your own question now Share this conversation Related Printers Questions Question Date Submitted Model PIXMA MG4160 - LCD message is Support

characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 6 8123798 Login|Contact Us Printers Printer Repair Questions? Roberts Your Own Question Charles A. CLEAN the shiny silver bar that is connected to the carriers using a dry cloth, from left to right in one direction.9. most probably u cant purchase it anywhere.if the encoder strip is still present, check if it is still positioned properly, at the back of the carriers because it guides the carriers

it Ci scusiamo per l'inconveniente. This one still prints black, blue and yellow fine. Leave the power cable disconnected for 30 seconds. 4. After about 2 hours of work.