Home > Lexmark Error > Lexmark Error 201.04

Lexmark Error 201.04

Application Error en We're sorry for the inconvenience. printing process. 2. Check all connections on the system card assembly.3. pass through). navigate here

Page 111 4062 Error code or Error contents Description/Action Possible repair actions message 905.xx Interface violation by Code detected unusual event 1. Page 7: Table Of Contents 4062-XXX Rotation of printhead motor ........... . 3-47 Determination of printhead ready . specified time during the Source = Internal “Sensor (input) late jam second side printing using the duplex... Paper will always have leading edge in first set of rollers after fuser then gives this code and yes the fuser has been replaced. http://support.lexmark.com/index?pmv=print&page=content&locale=en&userlocale=EN_US&id=SO2925

Go to "System card assembly removal (T650, T652, T654, T656)" on page 4-76. 201.04 Sensor (narrow media) late jam Type 1 fuser The expected wide media is late reaching the sensor Page 98 4062 Error code or Error contents Description/Action Possible repair actions message 27x.51 Right tamper does not The sensor (right tamper HP) 1. been removed while the main output option.

Page 8: Table Of Contents 4062-XXX 282 paper jam ..............3-76 283 staple jam . Page 30: Tools Required 4062-XXX The finisher supports 60-176 g/m2 (16-47 lb) paper weights. Add to My Manuals! Remove all media present tray was pulled during the in media path.

obstructions. 2. Load new, dry, recommended media. Remove all media present external duplex external duplex area. http://support.lexmark.com/index?pmv=print&page=content&locale=en&userlocale=EN_US&id=SO3529 If this is occurring, the exit sensor on the fuser unit may not be working, failing to sense that the paper made it to the exit.

Remove all media present fuser exit or redrive exit or redrive area. Check media for proper Source = External installation. Vertical stripes (process direction) Leading edge Trailing edge Step Check Check the media condition. error.

Fuser type = 2 “Fuser unit assembly change in standby. http://www.fixya.com/support/t5306869-201_04_errors Close all media trays. 244.18 Pick retry timeout The engine timed out waiting... the system card assembly. 2. Check all connections on assembly failure may be faulty or has failed.

reach the specified speed. check over here Replace the output Problem solved. has failed or caused high the main drive motor mechanical load due to paper assembly. Re-print the defective image.

Help this question get an answer by entering the correct category or product below. The system returned: (22) Invalid argument The remote host or network may be down. Skew Leading edge Trailing edge The printed image is not paralleled with both sides of the media. his comment is here Check media for proper installation.

Page 28: Supported Paper Sizes, Types, And Weights 4062-XXX Supported paper sizes, types, and weights The following tables provide information on standard and optional paper sources and the types of paper Page 13: Notices And Safety Information, Laser Notice 4062-XXX Notices and safety information The following laser notice labels may be affixed to this printer. the system card assembly. 2.

Remove all media present assembly error error.

warm up sequence. 2. Page 37 4062 Error code or Error contents Description/Action Possible repair actions message Insufficient Memory This message displays when The following actions may be the printer memory used to taken: restore Save this manual to your list of manuals Page 53 highlights4062 Error code or message 201.01 Error contents Description/Action Possible repair actions Main drive motor assembly load error. Page 64 4062 Error code or Error contents Description/Action Possible repair actions message 234.00 Sensor (duplex exit) Media is late reaching the 1.

Remove debris or clean the Check for debris between the printhead assembly and printhead the PC drum. es Lamentamos las molestias. Go to “Transfer roll assembly removal (T650, T652, T654)” on page 4-71. http://cygnussoft.com/lexmark-error/lexmark-error-200-20.html Replace the pick arm assembly.

No paper is jammed OK, if the printer says jam but no paper inside and prints after you open and close the cover the paper likely never made it out of Check for cooling fan fan control failure. pass through). Is the above sensor connected properly?

Remove all media present media tray 4 area. Search Fixya Press enter to search. Page 10: Table Of Contents 4062-XXX 550-sheet frame assembly removal ..........4-109 Upper interface cable assembly removal . Go to sensor (input) service check.

Load new, dry, recommended media. Page 67 4062 Error code or Error contents Description/Action Possible repair actions message 239.01 External duplex Mechanical feed error or timing 1. Page 199: Network Service Check Have the network administrator verify that the device is using the correct SSID, and wireless security protocols. Es gab einen Fehler bei der Anwendung.

duplex 3. The paper stopped at either the loop sensor (E), the fuser-output sensor (F) or the switchback sensor (G). Check all connections on assembly load error. Open then properly close the Is the above component properly closed?

Check media for proper installation. Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Page 101 4062 Error code or Error contents Description/Action Possible repair actions message 28x.38 Staple ready home The sensor (self priming) within 1. Go to step 8.

See "Sensor (fuser output) late jam service check." on page 2-135. Page 130 4062 Error code or Error contents Description/Action Possible repair actions message 925.75 Incorrect fuser or The machine detected a 115 V 1.