on March 8, 2012 at 6:19 PM Hi, just tried the technique as per instructions and had some success. on February 22, 2014 at 10:42 AM This comment has been removed by the author. Thanks for the resolution! Anonymous said... check over here
GREAT ADVICE - THANKS! Try a different software driver. 41.3 UNEXPECTED PAPER SIZE The printer detected a media size different from what it was expecting. I was asked to change the formatter card for the second time for my HP P2015dn. It was written off by IT. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00763560
Raw, Medium or Working ? Thanks again again again! Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations It works fine all the time since I baked the board!
If 49 error goes away, turn printer off, re-install EIO devices one at a time, and reboot printer each time to determine which EIO device is failing. 7. Someone probably has one that didn't go belly up this way. Also, note there are 2 versions of the formatter board -- one version has an RJ-45 network jack for network model machines (P2015N, P2015DN, P2015X) and one has only the USB Hp Laserjet P2015 Attention Light Blinking Replace the network card if needed. 5.
Put liquid flux under ALL of the BGA chips. I'm dancing, well in my head I am. However, it is possible. After it has cooled, remove the temporary standoffs, replace the stickers, reinstall the board into the chassis, and carefully plug in the cables.
Even if you found a new formatter board, it would die the same way anyway. Hp Laserjet P2015 Paper Jam Light Stays On Anonymous said... If all else fails, simplify the print job and print manageable segments at a time. 21 PAGE TOO COMPLEX The data (dense text, rules, raster or vector graphics) sent to the Forgot to take the stickers off the second one, and moved the cookie sheet to on top of the stove before letting it cool.
let's just hope it was a little flux burning off. on November 5, 2010 at 3:40 PM At 175 degrees Celsius: Circuit board baked, Worked at first try! :-)/[email protected], Sweden Venkatakrishnan said... Hp Laserjet P2015dn Error Lights No more paper jams! Hp Laserjet P2015 Manual Anonymous said...
on June 6, 2012 at 9:43 AM I was skeptical when read this well instruction, as the author mentioned "printer doesn't work now- so what do you have to lose?" Therefore, http://cygnussoft.com/hp-laserjet/hp-laserjet-5l-driver.html Anonymous said... Got given a 2015 that was not working. I am sooooooo happy :D Anonymous said... Hp Laserjet P2015 Troubleshooting
on August 1, 2012 at 12:10 PM Worked! Kai Gillmann said... Fewer led's lit, but still not working. this content thanks !!!!!!
Thanks again! Hp Laserjet P2015 All Lights On Except Paper on July 17, 2011 at 11:42 PM @Just Another Jenny, @RichardAwesome! Once your eight minutes is up, turn off the oven and open the door to let it cool in place.
That did the trick! Pro Slate 12) OR Browse all HP products Please wait while we process your request. Patrick said... Hp Laserjet P2015 Paper Jam Light Blinking santi said...
USB 케이블을 뽑았다가 다시 꽂습니다. 오류가 계속될 경우 HP 고객 지원 센터에 문의하십시오. 52 50005 레이저/스캐너 오류. 레이저/스캐너가 제대로 작동하지 않습니다. 프린터를 껐다 켭니다. 오류가 계속될 경우 HP 고객 지원 센터에 I'm so proud of myself that I didn't fuck it up! :-)Does it make sense to keep the printer turned off when not printing? HP Printer Support 352.321 προβολές 6:54 Renew your printer pickup roller! have a peek at these guys Anonymous said...
Baked the board in a Breville toaster oven at 350 for 8 min and let cool for a good 30 min. thank you. on May 20, 2010 at 8:27 AM Tried the "technique" last night. Thanks.
You can probably sell the used toners to Cartridge World or another store that rebuilds toner cartridges. viandant5 2.207 προβολές 3:48 HP 2015 Laser Printer Formatter Bake Repair - Διάρκεια: 10:11. cover off - never done that ever before. Thank you for posting this and saving us all lots of time, money and headaches!
Long answer: There is an IC on the board that uses a BGA form factor. on January 15, 2011 at 8:02 PM Rock On... on February 25, 2011 at 7:12 AM Pity, a printer which I baked about two months ago is acting up again (after a certain time, the printer seems to loose network After baking the board last night, it works like a charm!Many thanx!!!Rob McKennonUnix Admin.
It's best not to move the board right now, since all the solder is in a liquid state. It does work fine by USB though so that is a bonus. Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. on February 16, 2011 at 8:56 AM Very same problem with same printer.
Alan Jenkins said... Printer Thinker | Basic Printer Help 14.175 προβολές 0:45 Φόρτωση περισσότερων προτάσεων… Εμφάνιση περισσότερων Φόρτωση... Σε λειτουργία... Γλώσσα: Ελληνικά Τοποθεσία περιεχομένου: Ελλάδα Λειτουργία περιορισμένης πρόσβασης: Ανενεργή Ιστορικό Βοήθεια Φόρτωση... Φόρτωση... Φόρτωση... on October 6, 2011 at 9:15 AM This just totally saved my ass! Fixed the printer at the school and we have 5.