Home > Hp Laserjet > Hp Laserjet 4 Pickup Roller

Hp Laserjet 4 Pickup Roller

Contents

No action required. A Supplies Status report prints. I believe that if it doesn't get out of the fuser within a given time, you get a jam indicator. I tried feeding manually on paper tray 2 and the paper jams the same way. http://cygnussoft.com/hp-laserjet/hp-laserjet-5l-driver.html

Repair fees might apply for out-of-warranty products. If rollers and separation clutch are OK, disassemble printer to inspect the paper pickup drive mechanism for solenoid failure or drive gear misalignment (this is an advanced procedure).   Does the The page containing the error will automatically be reprinted. 41.3 UNEXPECTED PAPER SIZE This error most commonly occurs during one of the following situations: 1. by Anonymous on Feb 20, 2006 at 6:19pm Add comment Please sign in to comment 0 Yeah, kind of hard to email anyone named Anon E. http://fixyourownprinter.com/posts/62054

Hp Laserjet 4 Pickup Roller

by nivek on Oct 22, 2008 at 3:28pm Add comment Please sign in to comment 0 Thanks, nivek. Figure 14: Lower the scanner assembly Reconnect the power cord. Probably the one that comes in contact with the coupling gear you replaced would be the most likely candidate. It appears the paper is jamming as it is exiting the fuser.

there seems to be an issue that intermittently keeps the pinch rollers from activating at the proper time. In rare cases paper will simply stop moving inside the duplexer because another piece of paper was picked up too early, etc. On my LJ5 (not 5L or 5P or anything else) get a "Remove Paper Jam" error message. Hp Laserjet 4 Fuser by RJSparling on Mar 10, 2010 at 10:01am Add comment Please sign in to comment 0 To RJSparling,I've had pretty good luck with rubber cleaners and conditioners.

I can hear it running when it initializes, but I was wondering how likely is it that the motor might not be spinning the gears? Replace worn rollers as needed. 2. the jam occurs just as the paper leaves the back side of the duplexer and enters the bottom horizontal return path.

You'd have to take the assembly back out and inspect it.

I do have some working duplexers if you can't fix it. Hp Laserjet 5m It definitely had them, but not sure if they were more worn down as opposed to broken. No action required. If not open the rear door and check there its probably stuck in the fuser unit.

13 Paper Jam

If not then the motor or that gear assembly has issues. http://www.printertechs.com/printer-troubleshooting/paper-jams/307-paper-jams-hp-laserjet INITIALIZING The printer is performing initialization tasks after being powered on. Hp Laserjet 4 Pickup Roller I have tried this with the same paper (20#) that I have loaded in the other trays and with envelopes. Rg5-0886 by moe on Dec 19, 2002 at 5:43pm Add comment Please sign in to comment 0 Sounds exactally the same!

by RJSparling on Mar 11, 2010 at 11:14pm Add comment Please sign in to comment 0 I didn't know whether to say I'm a printer user or a technician.. his comment is here It does print fine from the MF tray. Everything ran smooth together before I put the assembly back in. And I mailed the results to support.I did replace tray 2 on the printer with one from another P3015dn (we bought 3 at the same time) last week thursday, no issue Hp Laserjet 4p Paper Jam

If you are on a network, contact your network administrator. 40 BAD SERIAL DATA FORMAT, PRESS GO KEY 40 HP MIO ERROR, PRESS GO KEY The printer encountered an error while No more paper jams! When I remove the jam, it will try and print it out again and we are in the same place. this contact form No problems so far.We have gotten the go ahead from HP to report DOA when the problem occurs again and replace the printer with a brandnew one.Kudo's for HP on this

Verify that the SIMM board is installed correctly and switch the printer back on. NOTE: HP recommends connecting the printer power cord directly to the wall outlet. help by Anonymous on Nov 26, 2008 at 11:34pm Add comment Please sign in to comment 0 Well open top lid and remove the toner see if you can see the

Figure 22: Open the rear access door Disconnect the power cord from the rear of the printer.

No action required. It printed fine for the end of the day. Press [Go] to return to READY MEMORY LOW, PAGE SIMPLIFIED This warning indicates that available memory was not sufficient for the print job. A faulty sensor never sees the end of the paper, so it times out and assumes a paper jam which stops the printer.

Insert the appropriate envelope size into the MP tray. Figure 6: Close the jam-access cover Close the ADF input tray. RESETTING ACTIVE I/O This message is displayed during an Active I/O Reset. http://cygnussoft.com/hp-laserjet/hp-laserjet-m2727nf-error-79.html Press [Go] if the desired size is already in the tray.

Insert a toner cartridge or make sure the cartridge is fully seated and the top cover is fully closed. If not then the motor or that gear assembly has issues. No action required. Where does the leading edge stop?

Reply 0 0 « Previous 1 … 4 5 6 7 8 Next » « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic My question is what should I be replacing, the side rails perhaps, or could it be the gears on that mesh with the toner are poorly aligned? Try to simplify your rpint job by using fewer graphics. by moe on Dec 10, 2008 at 10:05pm Add comment Please sign in to comment 0 My HP Laserjet 5 keeps jamming both automatically and in the manual feed.

Press [Job Cancel] to stop the test.