Now I cannot print anything, everytime I try to print I get this error. Top cover 1. Remove three screws. 2. Slightly raise the rear of the cover, slide the cover toward the front of the product, and then remove it.Laser Scanner Removal1. So Hewlett Packard seems to have worked the bugs out in that area compared to the P3005 model. The question that comes into play here is what part of this loop is failing causing a 51.1 error. Check This Out
Release one tab on the air duct, and then lift the air duct out of the product. 2. Remove the antistatic sponge. 3. Disconnect one connector and one FFC. Make sure that the door is completely open. 2. Disconnect one connector, and then remove one screw. 3. Slide the control panel toward the front of the product to release it. This leads me to conclude that the second laser is only used in 1200 dpi mode. It's not that hard a job. Get More Info
www.number.com says: February 1, 2016 at 9:51 amPermitting filters and cooling coils to turn out to be clogged from grime could make the unit work inefficiently, and the internal compressor or Word has it that one of the two lasers is not functioning correctly causing the 51.1 error. This area detects the beam and turns it back into an electrical pulse that the engine controller uses to synchronize the laser beam as described before.
Pinch the ends of the arm to disengage it from the lid. It might be necessary to use a small flat-blade screwdriver to release the tab inside that small hole. Hold the output assembly in place (located at the top toward the rear This sensor turns the light impulse back into an electrical impulse, which the engine controller uses to locate and synchronize the beam. Hp Laserjet P3015 Error Codes This dual line scanning enables the printer to create its true 1200 dpi image and keep printing at 25 ppm.
Open the rear door. 2. Gently pull down on the door and lower the door until it is fully open. 3. Hp Laserjet P3015 Laser Scanner Assembly Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Lift the laser/scanner up and out of the product.HP LaserJet Enterprise P3015 Series Laser/Scanner Assembly, LJ P3015/M525mfp RM1-6322-000Conclusion about the 51.10 error in the HP laserjet P3015 PrinterHopefully the 51.10 error http://www.imagesourcemag.com/ism-article/511-errors-4100-printers Results 1 to 5 of 5 Thread: HP LaserJet 4100 - 51.1 Printer Error Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 03-25-2005,01:41
So I called HP and they told me the part was $281, ouch! 51.10 Error Hp 4250 What's New? I found 1 article on the web stating it was the Laser scanner and that 51.1 is a beam detect error. This is done by turning on the laser when it is focused off the image drum and onto the beam detect mirror which again sends it to the beam detection sensor
Reply 0 0 wiremans1 Student Posts: 1 Member Since: 04-02-2015 Message 3 of 3 (21,824 Views) Report Inappropriate Content Re: HP LASER JET 3015 SHOWING ERROR 51.10 Options Mark as New More Bonuses Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets 51.10 Error P3015 A critical firmware error has occurred that caused the processor on the formatter to abort the operation HP laserjet 4300 49.24.02 error A critical firmware error has occurred that caused the Error 51.10 Hp Laserjet P3015 Solution However, it is interesting to note that with two lasers, the laser data is sent to the laser PCA via four independents wires.
This is the feedback system that initially helps synchronize the laser beam and keep it synchronized. I was surprised to find out that several other people had complained of the same problem. Second Laser Diode The second laser diode is placed right over the top of the first one. Would you offer guest writers to write content to suit your needs? Hp Laserjet P3015 Laser Scanner Assembly Replacement
I will look into that!Could you possibly point out in the picture at http://computer.howstuffworks.com/laser-printer2.htm which part I'd be looking for?BTW, if my girlfriend prints via my PC (printer shared via both Hp Laserjet 4100 Error Codes Troubleshooting Light or Faded Print - HP Laserjet Printers MP Tray 1 Constantly Lifting - HP P3015 Laserjet Printer-Solenoid FixParts and Supplies StoreBrother Parts / Supplies Canon Parts / Supplies Copystar Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting
While carefully working with the laser on our 4100, (do not try this at home as it can be dangerous) in 600 dpi mode, print was either fully present on the Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations The interesting note of a possible failure of the engine controller in this instance has traditionally been either a hard failure or it works fine. Hp P3015 Laser Scanner Most of the roads seem to point to the laser scanner as the culprit of this 51.1 error.
Slide the DIMM cover toward the back of the product to release it. 2. Reply With Quote 03-29-2005,09:03 AM #5 Brian View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Dec 2004 Posts 217 I've seen this error a few by moe on May 23, 2012 at 2:00pm Add comment Please sign in to comment Please sign in to comment HP LaserJet 4100 Buy discount ink Buy this printer More HP Release three tabs.
Reply With Quote 03-28-2005,09:38 AM #4 mattchall View Profile View Forum Posts View Blog Entries View Articles Member Join Date Mar 2005 Posts 53 If the mirrors/ lens of the scanner If your customer complains of the 51.10 error and you can't duplicate the problem then print of the error report in the diagnostic menu or in the same menu go to If there is an error in this process, a 51.1 beam detect error could occur. I note this because our repair department attempted to fix a 4100 with an intermittent 51.1 error and after replacing the laser scanner, the unit returned with the same problem.
Without this, the print on the page could wrap off one edge of the page and then back onto the other side, with the white edge of the boarder somewhere down Last edited by coodbgood; 03-25-2005 at 11:48 PM. They also suggested I use the replacement part RG5-5100. Left cover 1.
Karri says: August 6, 2016 at 9:42 pmNo obstante, el tratamiento fue llamado de este modo por obtener resultados parecidos al procedimiento estético facial. Help!