Home > Error Code > Lg Air Conditioner Error Code Ch 10

Lg Air Conditioner Error Code Ch 10

Contents

Learn More Date First Available December 26, 2012 Warranty & Support Product Warranty: For warranty information about this product, please click here Feedback Would you like to update product info or Please enter a valid email address. it fixed my "CH" "01" error due to a bad cooling coil sensor. (the bullet shaped one stuck against the cooling pipes)Published 5 months ago by Brigitte Couture5.0 out of 5 Disconnect from PCB measure resistance. 10 kOhm at 10C and 4 kOhm at 30C. http://cygnussoft.com/error-code/lg-air-conditioner-error-code-ch-05.html

Set ALL indoor units to cooling or ALL to heating to clear. Set to Sg for 1 unit, or Gr for group then reset power 04 RAC Product = Heat Sink Sensor Error, Open/Short Cct or over 95C. If not replace sensor. Multi V: 1 Vdc = 8 bar up to 2.5 Vdc = 37 bar CH44 Outdoor unit air sensor fault.

Lg Air Conditioner Error Code Ch 10

Disconnect from PCB measure resistance 237 kOhm at 20C and 168 kOhm at 30C. Either defective CNU or Central controller initialisation failure 245 Central controller data sending time out. Check pressures, and check service valves open 36 no such fault code Text 1, 2 or 3 digit fault code number only.

RepairClinic.com 36.970 προβολές 5:30 Mitsubishi mini split troubleshoot inverter board - Διάρκεια: 2:02. HL Condensate pump float switch risen. Took 15 minutes.Read more22 comments| 9 people found this helpful. Lg Air Conditioner Error Code Ch 34 If no Voltage is present the the PCB is faulty, if Voltage is present the fan motor will be Faulty. 09 Split = Outdoor unit fan problem.

and to APO/FPO addresses. Lg Ac Error Codes If you see fault code CH07 only type 7 in your text message CH31 no such fault code Text 1, 2 or 3 digit fault code number only. Check refrigerant 153 Excessive discharge temperature rise 105C Sub condenser 2 standard compressor. This code may refer to the sensor or control board.

Multi V = Indoor unit EEPROM error - Replace the indoor unit PCB, and then make sure to do Auto addressing and input the address of central control. 9 Split Lg Air Conditioner Error Codes Pdf If OK replace PCB, if not replace sensor CH45 Outdoor unit coil sensor fault. If no pump check blue jumper plug is inserted in socket CN Float. I would suggest that you provide the model # of your product so your expert will be able to research and provide you the best possible answer.

Lg Ac Error Codes

check fuses, if fuses OK replace outdoor main PCB 151 Faulty 4 way valve. you could try here Check refrigerant 103 Excessive discharge temperature rise 105C Sub condenser 2 standard compressor. Lg Air Conditioner Error Code Ch 10 Compressor damage(Insulation damage/Motor damage) 3. Lg Air Conditioner Error Code Ch 02 If OK replace PCB, if not replace sensor 46 Outdoor unit suction sensor fault.

Input voltage low 4. check over here To learn more about Amazon Sponsored Products, click here. check fuses, if fuses OK replace outdoor main PCB 149 Sub 2 check power supply voltage to the outdoor unit is correct (1ph 220 Vac 10% or 3ph 380 Vac 10%). I wired around the breached trace and now it is working great. Lg Air Conditioner Error Code Ch 05

You can always email me with a heading like Crochet Questions, and I will walk you through the steps. If you see fault code CH07 only type 7 in your text message CH59 no such fault code Text 1, 2 or 3 digit fault code number only. Mar 15, 2015 | LG LMN125HVT Air Conditioner 1 Answer Panasonic fault codes H14 = Indoor intake air temperature sensor abnormality. http://cygnussoft.com/error-code/lg-air-conditioner-c5-error.html Splits = Compressor Over Current (CT2), also see Code 06. 7 Multi Splits and Multi V = indoor unit is set to run in a different mode from the master indoor

Disconnect from PCB and measure resistance. 10 kOhm at 10C and 4 kOhm at 30C. Lg Dehumidifier Ch 01 Error Code Trending Average amount of energy a fridge uses each month? If OK, mismatching of controllers, or defective CNU 244 Central controller data receiving time out.

If OK replace PCB, if not replace sensor 124 Sub 1 outdoor unit coil sensor B fault.

Different Micom S/W Version 3. The information you have received from James is very good for the bucket light flashing. Disconnect from PCB measure resistance 237 kOhm at 20C, 168 kOhm at 30C. Lg Mini Split Error Codes Check wired correctly, if so check dipswitch in RC.

Ken Chan 44.901 προβολές 3:46 LG Air Conditioner Troubleshooting - Διάρκεια: 2:46. Sorry, there was a problem. Check comms wiring is correct, and check initialisation has been carried out correctly CH12 no such fault code Text 1, 2 or 3 digit fault code number only. weblink if not replace sensor.

Check the traces on board using very high magnification and use an ohmmeter. This is caused by the Indoor fan being locked. Split = text 21 CH07 Multi Splits and Multi V = indoor unit is set to run in a different mode from the master indoor unit. Commercial Product = Condensate pump float switch risen.

I have found some marvelous videos on how to do things on YouTube. Wrong setting of the HR unit Rotary switch and Dip switch 3. Ask Anonymously Popular Questions 7 Answers What is the Dry setting on air conditioner? Please try again.

Your question was published, help is on its way! All rights reserved Last updated - 11/10/2016 Skip to content Sign In Join or Activate Products Departments Departments Shop Shop Explore Explore Advice Advice Rewards Rewards More More