Home > Error Code > Lexmark Printer Error Messages

Lexmark Printer Error Messages

Contents

Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra Error 38 38 Memory Full Memory used to store pages is full. Check This Out

Replace the Autocompensator Assy. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. Reconnect.

Lexmark Printer Error Messages

Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr.

Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Fan the media and ensure it is properly installed. 2. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. Lexmark Printer Error Lights Error 47 47 Font Card Removed While Printing Printer needs data on removed card.

Check the operation of the toner sensor. Lexmark Printer Error Code Ec5 Go to sensor (input) service check. Make sure the memory shown on the printout matches the installed memory. Error 921 Fuser is below standby temperature when idle.

Error 26 Duplex unit is installed but paper tray is not sensed. Lexmark Fax Error Codes The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Error 27 Envelopes/paper loaded are wrong size. We sell only remanufactured ink and compatible cartridges for Dell, HP, Canon, Epson and Lexmark printers.

Lexmark Printer Error Code Ec5

Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers http://support.lexmark.com/index?page=content&id=SO4438&userlocale=EN_US&segment=SUPPORT&productCode= We can email further info if needed for your particular model. Lexmark Printer Error Messages Check the toner metering cam on back of suspect cartridge. Lexmark Error Codes Problem To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page.

The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. his comment is here If an open circuit, replace the lamp or fuser. Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Printer and Ink Networking Printers Printer Accessories and Applications Printer Downloads and Applications Printer Ink Cartridge Videos Printer Maintenance Printer Manufacturers Printer Paper Printer Reset Methods Printer Tips and Tricks Printer, Lexmark Engine Error

POR several times Check each board for secure ground. Check fan connector and cable for loose or damaged connection. Scroll Down to your error code.... http://cygnussoft.com/error-code/hp-printer-error-codes-list.html The pin should enter the tower on the HVPS and depress the cover switch.

Make sure the memory shown on the printout matches the installed memory. 938.06 Service System Electronics Use caution when measuring AC voltages. Error 920.X and 922.XX may display for a cold fuser.

ERROR 22 The exit sensor was not unmade in time.

Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Lexmark Ms310dn Error Codes Check connecting cables for continuity.

Replacement of the thermistor is not a cost effective repair, replace fuser assembly. See “Network Wrap Tests” on page 23. Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input navigate here Remove toner cartridge for better access to jammed paper.

Lexmark Laser Printer Error Codes Lexmark is a leading developer, manufacturer and supplier of printing solutions including laser and inkjet printers, associated supplies and services for offices and homes in more