Home > Error Code > Konica Minolta Bizhub Error Codes

Konica Minolta Bizhub Error Codes

Contents

You may have to register before you can post: click the register link above to proceed. you can remove all of the self-cleaning rig from the t/s unit, that comes with PM kits. If the substances get in the eye, rinse with plenty of water immediately. Page 65: Drum Unit HOME DRUM UNIT DRUM UNIT Composition Charging corona unit Cleaning/Toner-recycle section Cleaning section Separation claws Drum Drum Charging corona unit Separation corona unit Transfer corona unit Paper http://cygnussoft.com/error-code/konica-minolta-bizhub-350-error-code-c2557.html

Page 174 No conversion risk of incorrect detection due to extraneous light. Enter the 36 mode. [36 mode menu screen] [36 mode menu screen] Press the [2. Paper size detection for bypass tray Paper length in the by-pass tray is detected by PS20 Paper size detection for upper and lower ON/OFF. Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! find more info

Konica Minolta Bizhub Error Codes

motor 2: other than 7020/25/30) and the PRDB (printer driver board). 2.01 to 2.07 V 0.10 sec. 2.08 to 2.15 V 0.20 sec. Step Operation procedure Also, it is possible for the collected data to be checked by Enter the 25 mode. hit start, the machine will take about 5 minutes to complete this adjustment, it will display "ok" in the screen when it has successfully completed the adjustment. Page 202 HOME ADJUSTMENT RADF vertical magnification adjustment Restart timing adjustment To adjust the restart timing.

Page 49: Drive Section HOME DRIVE SECTION DRIVE SECTION Composition Main motor (M1) Toner supply motor 1 (M4) Toner supply motor 2 (M10) * Other than 7020/25/30 Paper feed drive motor must be removed when the DB is installed. Page 73: Developing Unit HOME DEVELOPING UNIT DEVELOPING UNIT Composition Developing unit cover Developing sleeve Developing regulator plate Developing sleeve Agitator wheel Agitator screws Mechanisms Mechanism Method Developing 2-component developing Developing Minolta 6001 Codes List Mode • The toner-out stop conditions vary according to 50 sheets the settings of DIP SW3 – 2 and DIP SW2 – 0. 45 sheets 40 sheets *4 : 1-shot message

Page 14 HOME SAFETY AND IMPORTANT WARNING ITEMS CAUTION: Ventilation • The copier generates ozone gas during operation, but it is not sufficient to be harmful to the human body. Konica Minolta Error Deletion Page 113 HOME DRIVE SECTION Removing the Ribbon Cable Reinstalling the Ribbon Cable (7135 Only) (7135 Only) a. Page 89: Fixing Unit HOME FIXING UNIT FIXING UNIT Composition Fixing guide Fixing guide Neutralizing brush Fixing claws Fixing cleaning roller Fixing web Fixing exit plate Cleaner cover Fixing Fixing heat Results 1 to 4 of 4 Thread: Konica 7020 - error F26-1 Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode

Caution: Be sure that the power cord has been (5) Remove the 2 set screws (through the holes in the unplugged from the outlet. Konica Minolta C451 Error Codes List Page 56 HOME READ SECTION Original Reading Control Operation The light from the exposure lamp reflects back from the original, passes through a lens, and hits the CCD sensor. Page 203 HOME ADJUSTMENT Engine restart timing adjustment RADF restart timing adjustment Step Operation procedure Step Operation procedure Enter the 36 mode. Credentials confirmed by a Fortune 500 verification firm.

Konica Minolta Error Deletion

Register Help Remember Me? http://www.officeimagingsystems.com/id169.html Page 23 HOME LIST OF DIFFERENCE 7020 SERIES LIST OF DIFFERENCE... Konica Minolta Bizhub Error Codes Procedure a. Konica Minolta Bizhub C6000 Error Codes Page 79 HOME CLEANING/TONER RECYCLE UNIT CLEANING/TONER RECYCLE UNIT Composition Cleaning blade Collected toner Cleaning conveyance screw blade Toner collection sheet Collected toner conveyance screw Mechanisms *Toner recycle Toner collected by

Sep 02, 2008 | Printers & Copiers 1 Answer Konica 7020 copier 35-9 is a low temperature error in the fuser.If the fuser has a problem it will not make a http://cygnussoft.com/error-code/konica-minolta-error-code-c-0214.html Page 75 TDS output voltage Replenishment Time sensor), M4 (toner supply motor 1), M10 (toner supply ≤ 2.00 V 0 sec. Mrbonz Jul 20, 2008 | Printers & Copiers 1 Answer Solution for KONICA 7020 E-56 is a main board problem. Separation Wires Spark arrestor plate Caution: Do not remove the paper entrance guide (rear) plate. Minolta 6001 Error Codes List

Please enter a valid email address. Timing adj.] in the 36 mode menu Enter the 36 mode. ribbon cable connector from the CCD. http://cygnussoft.com/error-code/konica-minolta-bizhub-c250-error-code-c2557.html Page 114 HOME Blank page 3-B-6...

a. Konica Minolta Error Code 107 Posted on Apr 15, 2008 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Daniel Hutchinson 4 Answers SOURCE: Konica 7022 the Code is indicating that the Fuser/Fixing unit is not getting hot enough if the code comes back do not reset but have a technician come look at the machine.

Connecting the ground lead to an improper point such as the points listed below results in a risk of explosion and electric shock: a.

Replacing the Loop Clutch (4) Remove the E-ring. Changes may have been made to this equipment to improve its performance after this service manual was printed. Counter value shown on OB 2-M-5... Minolta Photocopier 6001 Codes Do not remove caution labels.

Page 158 HOME Blank... You can then remove the fixing cleaning roller. Solution: This is occasionally a false alarm. Check This Out A risk of fire exists. • Check the interlock switch and actuator for loosening and check whether the interlock functions properly.

Select the [2. Copy count by each size Enter the 25 mode. [25 mode menu screen] Paper size for destination Size Press the [3. Hewlett-Packard Company. Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Konica Minolta DiALTA Di200 Copier Open Question How to clear error code F

start date, and the screen below will appear automatically. HAD MY COMP IN STORAGE FOR COUPLE OF YEARS, WANT TO 10/18/2016 10/18/2016 Barun It won't boot. Page 66 OFF after the specified period from when PS3 sist in separating the paper from the drum. (paper exit PS) (or PS2 (fixing exit PS) for machines other than the