Home > Error Code > Kitchenaid Error Code F2e1

Kitchenaid Error Code F2e1

Contents

Reply With Quote November 7th, 2006,11:14 PM #2 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,624 These Reconnect power and plug unit in. Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Use the My Appliances resource to quickly access material for your registered appliances. http://cygnussoft.com/error-code/kitchenaid-oven-error-code-f2e1.html

Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature. F4-E1 -Meat Probe Defect - This error indicates a problem with either the probe, receptacle, or probe circuit. Check for drain pump failure and clean it of any debris. out, you may end up spending a couple hundred on a new Control board 9782435, etc.

Kitchenaid Error Code F2e1

Click here for more details. Turn off hot and cold water to faucets and unplug the unit before proceeding. When none of that works, it's time to call a professional. Much appreciated friend!

I would first check in the back of your range, behind your back access panel, check all the wiring to see if any wiring is burned or shorted to your metal Reconnect power and plug unit in. Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Kitchenaid Oven Error Code F6e0 E5 - Dry Rack Sensor - If the signal is lost during a Dry Rack cycle, all outputs will be turned off and this error code will appear.

F13 - Internal CPU checksum Error(s) - Disconnect power for one minute and check to see if error reappears once power has been restore. Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. If error continues, disconnect power and replace control. http://www.applianceblog.com/mainforums/threads/6276-KitchenAid-Range-Oven-F2-E1-Error-Ignitor-problems Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU).

Replace failed component. Kitchenaid Oven Pf Error Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. SUD - Suds Lock (Too Much Detergent Detected) - Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power.

Kitchenaid Oven Error Code F2e1 Stuck Shorted Key

If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. and 8 p.m. Kitchenaid Error Code F2e1 The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd. Kitchenaid Refrigerator Error Codes The metal will bend a little and should stay in whatever position you put it in.

If present, replace control board (clock). Check This Out Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. If error still remains after power has been restored, replace touch control module. (control board) F12 - Electronic Board and Touch Module Communication Error - Disconnect power for one minute and Kitchenaid Oven Error Code F2e0

Replace failed component. F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Make sure there is not a siphon problem and check all hoses for possible leaks. Source This should change to the F02 error code after a few minutes.

F06 - Drive Motore Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power. Kitchenaid Oven Error Code F9e0 The solenoid was activated, but each time, the ratchet mechanism would stick preventing the door from being unlocked. If connections are not damaged, reconnect power and hold down any key until the F5 error clears.

If error continues, replace board connection cable between touch control module and electronic control.

Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. By resetting the board, you are giving the appliance the chance to reboot it's program and hopefully return to a functional condition. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Kitchenaid Dishwasher Error Codes Thanks.

Replace failed component. Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Yes No Thanks! http://cygnussoft.com/error-code/kitchenaid-oven-error-code.html Most of these control boards have microprocessors on them and just like the computer you are reading this post on, are sometimes susceptible to confusion.

Fixing a small problem would be great, but locating it could be a nightmare. Reconnect power and plug unit in. The cycle began like normal with the door locking, but after the cycle was complete, the door remained locked, and an error message was displayed in the screen. Replace failed component.

If error continues, replace board connection cable between touch control module and electronic control. Log in to Reply Andrew Bracy on December 17, 2010 at 2:00 pm Wow what a great posting here for an easy and free fix! Verify CCU is working by performing diagnostic test or any cycle. Check the inlet valve and pressure switch for proper shut off and operation.

Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Check the drive system for any worm or failed components and reconnect power and plug unit in. F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Also check for any causes of high resistance in the oven temperature sensor circuit.

F15 - Motor Control Unit (MCU) Error -Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). I'll let you know how it goes. What's New? The problem has been resolved.