Add memory or simplify the print job. The link addresses the Scanner Error 12 but not 20. Hold down the front panel button to display the error LED code. For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect. 22 ERROR/ I/O CONFIG ERROR 1. http://cygnussoft.com/error-code/hp-printer-error-codes-list.html
At least one of two tabs must be present. 3. If the board becomes defective, you will receive an error 12. X Description 2 Fan 3 - Formatter Fan (intake) 3 Fan 2 - Laser/scanner (exhaust) 5 Fan 1 -Low-voltage power supply (exhaust) 6 Fan 4 - Face-down delivery (exhaust) 9 Fan Either or both may have a fault, although this can sometimes be attributed to a faulty fusers, laser assemblies, firmware DIMMS or driver problems.
You can depress these by hand and hear them click. DC Power Supply malfunction. 2686 Only: 1. What to do:If you have an older model then reseating or changing the memory may resolve the issue.
Check that ROMs are in correct location and orientation. 3. Computer is powered off Unseated or defective MIO card 5P Indicates an abnormal connection break occurred while transferring data from the computer 41 Error (Temporary print engine failure) All printers Reset Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.When a solution is found please mark the post that solves your issue.Every problem has a solution! Hp Error Code Oxc4eb827f If error goes away replace SIMM Replace formatter PCB 5P SIMM malfunction.
Replace main motor. Hp Laptop Error Codes Your cache administrator is webmaster. Some of the test points referred to in this document require special safety equipment, tools or meters as well as familiarity and training on laser printers. http://www.all-laser.com/aerror-code/ Replace Main Motor PCA or Main Motor. 4.
Reinstall the stacker or staple/stacker 3. Hp Printer Error Code List Pdf IIISi/4Si 1. All rights reserved. System error 21:11 A problem has been detected with the Service Station assembly.
b. http://www.advancedlaser-hp-error-codes.com/ Bad registration sensor or bad fuser exit sensor. Hewlett Packard Printer Error Codes Check these items. Hp Computer Error Codes HP Error Code:63 - Defective Formatter Board Explanation:Your printer either has improperly fitted or bad memory Simms or a defective formatter board.
Wait for RESET MAINTENANCE COUNT to be displayed and then release both keys. NOTE: Some versions of the 4000, 4050, 4100, and 5000 will NOT have their maintenance count reset his comment is here HP Error Code:69 - Duplexer Error has Occurred Explanation:The printer has a problem with duplex unit, this is the unit that enables the printer to print double-sided. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. HP Error Code:67 - Service Printer Error or Memory Error Explanation:Depending up your model this can be a number of different things including: a temporary error, defective paper guide, a break Hp Inkjet Printer Error Codes
How did we do? IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si Alternatively you can install additional memory if available. this contact form Press the up arrow (Navigation) button until the message New Maintenance Kit appears on the control panel display. 7.
Resolve same Damaged fiber optic cable. Hp Printer Error Code 0x610000f6 II, III Only: 1. For example, they could appear as 49.4C03 SERVICE ERROR HP LaserJet 4000, 4050 and 4100. 50.X FUSER ERROR a fuser error has occurred.
II, III Replace cable from DC Controller PCB to HV power supply. We stock HP LaserJet maintenance Kits for fast onsite printer service in Los Angeles, Orange County & San Bernardino! A message New Maintenance will appear in the control panel display and the printer will reset. Hp Officejet Error Codes temporality for around 1 day it ran as before, but again ERROR 12.
You may need to reseat the memory DIMM's or replace the firmware DIMM or formatter board. Clean around corona wires and ensure proper grounding of registration assembly and transfer area See error 51 2686A/D Perform laser power adjustment II, IID, III, IIID Replace cable from DC controller What to do:Try resetting the NVRAM. navigate here Watch the termination's on the network cabling.
Check paper feed roller. What to do:Try simply reseating the memory chips. a. Here’s our quick guide to the most common HP printer error codes, what the error codes mean and how to fix them.
HP Error Code:80 - Defective Network Card or Formatter Board Explanation:Your printer has a defective accessory of some kind, possibly related to memory, I/O cards or a firmware issue. Check replace SIMM's 61.x Service All printers Reseat SIMM memory Replace SIMM's Replace formatter PCB 62 Service 2686A/D, II, IID, IIP, IIP+, III, IIID, IIIP, 4P Replace formatter PCB 62 Memory Take a sharp tool, like a razor blade and scrape the buildup off these edges. Sometimes you can clean a pickup roller and get a little more life miles out of them but when you start to get jams with a smudge on the top middle
The line voltage and current source at the printer location might need to be inspected to ensure that they meet the electrical specifications for the printer. You may be trying to incorrectly print transparencies through the duplex unit 4. Release the checkmark (Select) button. 6. Original HP Maintenance Kit always in stock HP LASERJET IIISi/4Si MAINTENANCE KIT C2062-67902 HP LASERJET 4/4M MAINTENANCE KIT C2001-69012 HP LASERJET 4 PLUS/ 5 MAINTENANCE KIT C3916-69001 HP LASERJET 4V/4MV MAINTENANCE
Replace or clean as needed. IIISi/4Si check the door open sensor flag, PS1. Sensor Arm Stuck or Broken - check for free movement of the sensor arm. General information with more detailed information available.
What to do:Update to the latest firmware to rule out this issue. Replace DC Controller PCA. 2. Note 2686D: If one clutch needs re-greasing it is likely that they all do. 4. Replace Fuser Assembly.
Verify that the SIMMS or memory cards are seated.