Home > Error Code > 931.01 Service Printhead Error

931.01 Service Printhead Error

Contents

Fuser Pricing How did we do? Error 38 38 Memory Full Memory used to store pages is full. Il ya eu une erreur à l'application. Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on http://cygnussoft.com/error-code/lexmark-x364dn-service-manual.html

If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Error 54 Serial Error - Framing or parity error on serial. Error 47 47 Font Card Removed While Printing Printer needs data on removed card.

931.01 Service Printhead Error

May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Application Error en We're sorry for the inconvenience.

Reconnect. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Change the contents of the old list and save it as new. Lexmark X658de Error Codes Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled.

I truly appreciate it. Lexmark Error Codes es Lamentamos las molestias. Make sure there is no paper jammed in the printer. his explanation If an open circuit, replace the lamp or fuser.

Use caution when measuring AC voltages. Lexmark Engine Error Houve um erro com o aplicativo. 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times. A secondary error indication can be obtained by pressing an releasing a button.

Lexmark Error Codes

Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? http://www.all-laser.com/aerrorlex/ Run the Quick Disk Test. 931.01 Service Printhead Error Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Lexmark Printer Error Messages Use saved Parts Lists as templates to create new lists.

Check LVPS cable for continuity. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Scroll Down to your error code.... Houve um erro com o aplicativo. Service Error 146.00 Dc Pick Motor

Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. The pin should enter the tower on the HVPS and depress the cover switch. Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input You can add, delete list items and change the quantity of spare parts.

Wayne Haub Kansas City Save time and money by servicing your own Lexmark printer Lexmark Laser Printer Error Codes Lexmark error codes may not apply equally to all models. Lexmark Dc Pick Motor Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit.

Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644

it Ci scusiamo per l'inconveniente. Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Lexmark Error Codes Problem Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective.

Error 921 Fuser is below standby temperature when idle. The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Replace with the correct printhead. There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact.

The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. Make sure the memory shown on the printout matches the installed memory. The transfer roller is included in the maintenance kit.

Replace low voltage power supply assembly. Observe the lamp through the left near side of the printer. Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Respond to this 0 It could be n-way failing to negotiate correct duplex.Select NETWORK>NETWORK OPTION 1>NETWORK 1 SETUPAfter entering this menu hold GO(5) and press

Your cache administrator is webmaster. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system C'è stato un errore con l'applicazione. Can you give me link directly to latest firmware for M410?

Error 44 Defective font card installed in font slot. Try opening Tray X.